Laminate Flooring Guide Floor Studio Decor Search

Search

Results 76 - 80 of 265

080 – Información sobre productos - SWISS KRONO ... Snap-Together Laminate Flooring – a Guide ... Unlike parquet flooring, there is no ... not to install laminate yourself. And as KRONOTEX is ... flooring, laying it is quite easy, even for inexperienced DIYers. ... The planks use a tongue-and-groove system ... simply snap them together without the need for any special knowledge ... follow a few basic rules before and after installation. ... Movie Clips ... #accessories #care & #repair ... Transport and storage Please transport KRONOTEX flooring carefully ... the original packaging. Use up each ... package before opening a new one. ... Large quantities should also be stored ... the original packaging to prevent damage. ... lengthy storage, panels must be placed horizontally ... the unopened packages in a heated ... Don’t lean snap-together laminate planks standing up against a ... This can cause them to bend, which would ... lay them down flat on the floor. ... Acclimate KRONOTEX laminate flooring by storing ... the unopened packages for at least ... hours in the room where the floor will ... be installed. This will prevent subsequent ... and buckling. Before laying KRONOTEX snap-together laminate planks, ... them once again to make sure they ... are undamaged, of the right size ... identical in appearance when viewed in daylight at ... the installation site. If you discover ... actual defects, read the information printed on the back ... visual defects, as this would exclude them from the warranty. ... Basic Rules for Laying Snap-Together Laminate Flooring ... Lay the flooring at an ambient temperature ... at least 18° C, a floor temperature of ... least 15° C and relative humidity between ... and 60%. These conditions should also persist during ... the first three days after installation. ... windows and doors closed the room while laying. ... Laminate flooring looks best when laid ... the planks parallel to the main ... source. Before starting to lay, calculate ... the width that the last row ... planks will have. It should not be less ... 5 cm. This may make it necessary to trim the ... KRONOTEX snap-together laminate flooring is intended to float ... the subfloor. In other words, it ... be glued, nailed or otherwise fastened. ... wood is hygroscopic, the laminate works and moves. This ... slight differences in height between the planks will simply enhance the ... appearance of this engineered wood product. ... Fix skirting boards to the walls, not the floor! ... Please follow the installation instructions precisely. ... the flooring is improperly laid, the ... will be voided. If any problems arise, ... the work immediately and contact your ... Step-by-Step Instructions for Installing Snap-Together Laminate Flooring ... After making sure that the subfloor is suitable ... letting the laminate flooring planks acclimate in ... the room for at least 48 ... If you are laying the flooring on screed, ... put down a damp-proof membrane. Roll the membrane out parallel ... the laminate planks and cut it ... size. At walls, the membrane should ... upwards by about 10 cm. Overlap sheets of membrane ... about 20 cm and glue them tightly together to prevent ... moisture from penetrating. ... The next step is to apply ... it at 90° angles to the direction that the laminate planks ... run and use sticky tape to fix them ... one another. ... Lay the first row of snap-together laminate ... Start in a corner of the room and lay the planks ... they run parallel to the window or other light source. ... the planks lengthwise along the wall ... a gap 10 to 15 mm wide and ... short sides together. Wood wedges are excellent spacers. You will almost ... have to shorten the last plank ... the row. To do so, use ... saw, a jigsaw or a special-purpose laminate cutter. The last piece ... be shorter than 40 cm. It ... be necessary to shorten the first ... well to prevent this (making sure that it is also at ... Start the second row with the piece ... was left over from the first. Simply insert it into ... the edge of the first plank, ... slightly up (at about 12°) and then press it down ... hear it audibly click into place. The last row of laminate ... will probably be too wide, making it necessary ... trim it. Remember to leave a sufficient gap along the ... Before attaching the skirting boards, first ... use a Stanley knife or cutter ... trim the excess membrane. It’s best to ... the skirting boards to size with ... mitre saw. ... Transition rails are mounted between different floorings in ... adjacent rooms. Depending on the type, they must be glued, ... or snapped into place. KRONOTEX has also summarised the ... Special Installation Situations 1. Heating Pipes and Room Dividers ... Where heating pipes or room dividers ... out of the floor, first cut the plank ... the right length, then lay it ... to where it will go and use ... folding rule to measure and mark where ... the openings are needed. Then cut ... drill out the marked spots. Here too, remember ... leave a 10-mm gap on all ... Saw the plank diagonally (mitre cut at ... 45° angle) up to the holes. This ... increase the surface area available for ... Apply D3 glue to the sawed-off piece and ... join it to the other piece behind the heating ... pipe or other element. ... Wooden doorframes should be shortened. Lay a plank next ... the frame with the décor side ... Use a suitable saw to sufficiently ... the frame, then slide the plank ... it with the décor side up. With steel ... make an appropriately shaped cut-out in ... the plank instead. ... 3. Expansion Elements for Large Rooms ... In rooms measuring more than 12 metres in the ... parallel to the planks and/or eight metres perpendicular ... element is also needed in the middle. This also applies to ... and rooms with complex shapes. We recommend removing the tongues on ... the edges of the panels along ... elements to ensure sufficient room for them to ... move. Full-Surface Gluing of Snap-Together Laminate ... KRONOTEX flooring can also be glued over the entire surface ... the floor. The required steps depend ... the kind of subfloor. It may ... be necessary to level it by ... primer or filler, etc. If there are height differences of more ... mm, they should be evened out so they don’t ... 1 mm. ... Make sure that the subfloor is ... dry, level, firm and clean. Leave existing expansion joints in the ... same places and align expansion elements ... the laminate flooring with them. Use ... polyurethane (PU)-based adhesive. If anything is ... or problems are encountered, consult a professional floor ... Important: Do not glue KRONOTEX flooring down over underfloor ... This would void the

Results 76 - 80 of 265

­

Cookie Einstellungen

Wir verwenden Cookies, um Ihr Erlebnis zu verbessern und Ihnen personalisierte Inhalte zu liefern. Durch die Verwendung dieser Website stimmen Sie unseren Cookie-Richtlinien zu

Notwendige Cookies
Statistische Cookies
Cookies von Drittanbietern
Akzeptieren Einstellungen bearbeiten
www.kronotex.com

Cookie Einstellungen

Weitere Informationen zur Verwendung von Cookies in unseren Cookie-Richtlinien.

­

Notwendige Cookies

Ohne diese Cookies können die von Ihnen angeforderten Dienste nicht bereitgestellt werden.

Statistische Cookies

Erlauben Sie anonyme Nutzungsstatistiken, damit wir unser Angebot verbessern können.

Cookies von Drittanbietern

Cookies von Drittanbietern, die eingebunden werden um personalisierte Anzeigen für Sie auszuliefern.

Cookies, die wir auf dieser Website verwenden